URWERK UR-111C Black

The UR-111C Black timepiece features a grooved case in black-coated steel and titanium curves along its ample length and width. The curved sides are held by transversal screws in half pipes.

The case is built around the unprecedented construction of the UR-111C Black’s movement, which put the indications at various and seemingly peculiar positions on the face. Furthermore, each indication is unconventional, if not original, according to URWERK’s signature horological speciality. The relatively bulky and unusually shaped movement could not be cased up in the ordinary way, through the top or the bottom of the case. It had to go in through the side. The case is therefore made up of three parts; the first two support the flanks of the movement while the bigger central part fits closely around it.

The same lateral thinking that conceived the lateral casing up of the movement is equally applied to every aspect of this timepiece which features glass plate indicating seconds alone, two different displays of the minutes on rollers, indications at the bottom of a sculptured case measuring 46mm long and 42 wide.

URWERK’s watches are deliberately puzzling because watches are not supposed to look like that. You do not immediately know how they work or how they are made. The UR-111C Black follows this fundamental rule. You will have to figure it out, but here are some clues. You will notice that there is no crown sticking out of the side of the case. Instead, there is a sort of lever. And then there’s this fluted cylinder across the middle of the face.

The two functions of winding the watch and setting the time have been separated. The short, knurled crown of the ordinary watch has been transformed into an accessible long cylinder that you roll with a thumb or finger to wind the watch. Fully wound, the UR-111 Black keeps going for 48 hours. To set the time, you swing out the lever on the right of the watch. This switches the roller to time-setting mode. Rotate the roller in either direction to set the time on the other cylinders. There are of course no hands on the UR-111C Black.

Double minutes
In 2009, URWERK introduced the CC1 King Cobra. It showed the time on a linear scale on a rotating cylinder and was the first of URWERK’s special project watches. This collection comprises timepieces with original indications and functions that are apart from URWERK’s wandering-hour based watches. The King Cobra was distinguished by its multi-level design with indications in separate zones and a complete absence of hands. In many technical respects, the UR-111C Black is its descendant.

Like the King Cobra, the UR-111C Black displays its indications on the bottom of the case. With the watch on your arm the indications are on the side of your wrist so that you can tell the time at a glance without having to turn your wrist. With your arm in its natural position when you walk, sit or drive, the time is always in your line of sight. URWERK has arranged the time display in three zones shielded by curved sapphire glasses. Reading from the left, the hours are marked in Arabic numerals on a rotating cone instead of by hands. The cone jumps forward to the next hour on the hour. Opposite, on the right side of the watch, a matching graduated cone rotates once an hour to give an exact reading of the minutes. Between the two, a wide window repeats the minutes in a stunning display that provides a new slant on the linear minutes of the CC1 King Cobra.

The linear minutes display consists of a rotating cylinder marked with a helix line spiralling along its length. As the cylinder rotates, a section of the helix line moves along a graduated scale of minutes marked at five-minute intervals. But in the UR-111C Black, the scale slants diagonally across the display instead of being in line with the axis of the cylinder. This means that the cylinder only has to turn 300 degrees to bring the helix to the 60th minute at the end of the scale. Then the cylinder snaps forward 60 degrees to complete the rotation, bringing the helix line back to its start position, in an apparently retrograde action. In the UR-111C Black, the markings are in orange, the helix in Kryptonite green, while both the 60th minute on the linear scale and the 60th second of the seconds display are in yellow.

Dispersed seconds
The studied and ergonomic layout of the UR-111C Black’s indications governs its design. The seconds are thus far from the hours and minutes, beyond the winding and setting roller, under a framed glass window. Digital seconds, orange against black, look strangely magnified as they pass across a circular window in sinuous progression. The five-second numerals are mounted on two wheels — split between even and odd numbers and appear in turn as the opposing wheels counter rotate. Each wheel with its numerals is skeletonised using a LIGA process, and weighs just 0.025 grams. The tiny numerals would be impossible to see were they not brought into visual range by a dense cluster of precisely aligned optical fibres situated a tenth of a millimetre above the numerals.

A matter of form
URWERK’s outstanding designs are matched by the dimensions of its watches. The extraordinary displays of time can only find their true expression if they are clear and visible — and that requires space. The volumes and shapes are also governed by the artistic vision of Martin Frei.

Yet the UR-111C Black is certainly the URWERK model that is most at home on a slender wrist. Comfort is assured by the form of the caseback, which follows the curve of the face of the watch. Try one on for a perfect fit of the bones and muscles of your wrists. You would not expect a timepiece of that unique size and shape to be so comfortable to wear. But then surprise is always part of the URWERK experience.

Technical details

Model: UR-111C Black – limited production of 25 watches

Calibre: Self-winding calibre with stop seconds
Jewels: 37
Escapement: Swiss lever
Frequency: 4 Hz
Power reserve: 48 hours
Materials: Anodized aluminum cylinder; LIGA-processed seconds wheels.
Surface finishes: Circular graining, sanding, côtes de Genève, polished screw heads.

Jumping hours
Retrograde linear minutes
Digital minutes
Digital seconds relayed by optical fibres

Materials: 316SL steel and grade 5 titanium, PVD coated in black
Dimensions: Width 42mm x length 46mm x thickness 15mm
Glass: Sapphire crystal with anti-reflective coating
Water resistance: Pressure tested to 30ATM / 100’ / 30m
Surface finishes: Sanding; satin finish

Retail price
CHF 130’000.00 (excl. tax)

Leave a Reply Cancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.