A patented chronograph function enables the Montblanc TimeWalker Chronograph 100 to perform a feat that’s seldom achieved by mechanical timepieces: it can measure elapsed intervals to the nearest 100th of a second. To accomplish this, the watch relies on the Montblanc Manufacture’s nearly century-old competence for measuring intervals to the nearest 100th of a second.
The Minerva Manufacture, which would later become the Montblanc Manufacture in Villeret, sparked enthusiasm among specialists in this disciple when it launched its first mechanical 100th -of-a-second stopwatch in 1916. Subsequent versions were equipped with a chronograph hand that requires just one second to complete a full 360° circuit of the dial. Precisely this principle is employed by the Montblanc TimeWalker Chronograph 100 with its newly developed manufacture calibre MB M66.25.
This high-performance manufacture calibre is embedded in a case crafted from materials which are used in racing cars and which further accentuate the movement’s innovative mechanisms. Highly advanced materials and mechanisms are uncompromisingly combined with a manufacture movement that is built in accord with the centuries-old tradition of the art of Swiss watchmaking.
Meticulous manual craftsmanship and decorative finishes uphold the rigorous standards of even the most demanding connoisseurs. In the Montblanc TimeWalker Chronograph 100, Montblanc’s watchmakers have successfully united performance-oriented innovation and the finest horological tradition.
For a watch to measure intervals with 100th -of-a-second precision, its balance must be able to vibrate at a frequency of 360,000 semi-oscillations per hour (50 hertz). In conventional chronograph wristwatches, one and the same balance drives both the ordinary time display and the chronograph mechanism for measuring elapsed intervals. Activating the “start” function creates a connection between the going train and the chronograph; this link is severed when the “stop” function is triggered.
Due to its need for a frequency of 360,000 semi-oscillations per hour, the Montblanc TimeWalker Chronograph 100 cannot rely on the same mechanical principle as a conventional chronograph calibre, which vibrates at a much slower pace of 2.5 or 4 hertz.
This necessity prompted the watchmakers in Villeret to devise a solution with two balances. A large, massy, screw balance oscillates at a frequency of 18,000 A/h (2.5 Hz) to ensure the precise rate of the going train, while a small balance paced at the extremely high frequency of 360,000 A/h (50 Hz) regulates the chronograph function.
Rather than remaining continually in motion, the separate balance for the chronograph begins to vibrate only when the “start” function is activated by a flexible steel lamella (called fouet) mounted behind the arrowhead of the chronograph rocker. When the “stop” function is triggered, this slender steel plate arrests the tiny 50-Hz balance and holds it motionlessly in place until the next elapsed-time measurement begins.
The chronograph function is powered by its own barrel, which stores enough energy to measure intervals up to 45 minutes in duration. An elapsed-time measurement can be indefinitely extended by turning the crown anticlockwise while the chronograph is running, thus adding fresh energy to the chronograph’s barrel. The going train for the ordinary time display draws its energy from a second barrel that guarantees a 100-hour power reserve.
The TimeWalker Chronograph 100 is equipped with two zero-return mechanisms: one for the 100th of a second and another for the elapsed minutes and seconds. The engineers at the Montblanc Manufacture in Villeret devised a patented mechanism with an innovative column-wheel control and a novel zero-return solution for the central 100th -of-a-second hand or trotteuse.
A two-level column-wheel separates the functional level for starting and stopping the chronograph from the zero-return level for the elapsed-time counters. The column-wheel bears four narrow and four broad pillars, between which alternately higher and lower switching levels are positioned. The higher level controls the chronograph rocker: its arrowhead carries the slender steel lamella that starts and stops the finely toothed 50-Hz balance.
When the measurement of an elapsing interval commences, the column-wheel gives an impulse to the chronograph rocker, which then moves away from the high-frequency balance and transfers the impulse via the steel lamella (fouet) at its tip to the balance, which instantly begins vibrating at an hourly frequency of 360,000 semi-oscillations.
When the measurement of the elapsed interval is halted, the column-wheel moves the chronograph rocker toward the chronograph’s balance so that the steel lamella presses against the balance’s rim, thus halting both the balance’s vibrations and the progress of the chronograph’s elapsed-time hands.
The lower level of the column-wheel is the switching plane for the beak of the heart-lever. This lever returns to zero the 60 elapsed-seconds hand, which is connected to the heart-lever of the 15 elapsed-minutes counter. Heart-levers and heart-cams act in the conventional manner to return these two counters to their zero positions.
By contrast, the zero-return of the 100th -of-a-second hand is accomplished in an innovative way. The 100th of-a-second wheel carries a disc with a catch. While an ongoing interval is being measured, the heart-lever of the seconds-counter wheel presses a little arrowhead-shaped lever with a barb away from this catch. When the chronograph’s hands are returned to their zero settings after the duration of an elapsed interval has been measured, the heart-level releases the little lever; a spring now presses the lever against the wheel with the catch. The 100th -of-a-second hand is freed to complete its unfinished circuit until it reaches its zero position, where it is halted because the catch of its zero-return disc engages with the barb of the zero-return lever.
The design and construction of the movement are extraordinarily innovative, but the manufacturing methods rigorously uphold horological tradition. The Montblanc Manufacture in Villeret is one of the few remaining manufactories where all of these time-honoured skills are still practiced. Plates, bridges and steel components are painstakingly and manually fabricated and decorated with circular graining and/or Geneva waves. Edges are manually bevelled; the bevels are then polished by hand and the flanks undergo brush finishing. Each balance-spring is individually counted by hand and by the artisan’s unaided eyes.
Meticulous handcraftsmanship is likewise used for the mise en fonction of the chronograph: here, the functional surfaces of all rockers and levers are abraded to match each other with tolerances in the 100th-of-a-millimeter range, and the ruby pallet-stones are exactly adjusted in the pallets. These tasks involve countless steps and require partial disassembly and subsequent reassembly of the movement until it runs with optimal smoothness – and the timepiece satisfies the perfectionists at Montblanc.
The tripartite case combines various materials that are commonly used in auto racing and that accentuate the innovative character of the movement. The titanium steel bezel is coated with a layer of extremely scratch-resistant DLC (diamond-like carbon). The screwed back is crafted from titanium and bears an inset pane of sapphire crystal. Titanium sheathed with carbon fibre forms the middle piece of the case: Montblanc crafts this sheath as a seamless, complexly structured cocoon rather than merely gluing a simple carbonfibre shell around the titanium carrure. Several dozen layers of carbon fibre, with the fibres in each layer oriented at 90° to those in the preceding stratum, are fused together with artificial resin at high temperature with a pressure of 10 tons.
This produces a compact carbon-fibre block. The case’s round sheath is stamped perpendicularly to the carbon-fibre layers to form a seamless “monoblock” which is then tautly stretched over the case’s titanium middle piece. The monoblock’s surface boasts a special horizontally striped pattern rather than the typically uniform texture of carbon-fibre. This intimate liaison between titanium and ageing resistant carbon fibre results in a lightweight yet remarkably robust case that optimally protects its precious mechanical inner life. The middle piece of the case is clamped between two pierced longitudinal titanium brackets. These transition into the characteristic skeletonised horns of the TimeWalker collection and give the case its distinctive TimeWalker look.
The large crown is likewise crafted from titanium and topped by an inset Montblanc emblem made of mother-of-pearl. Nonslip crosswise fluting around the crown’s flanks facilitates manual winding, which can be performed in two directions: turning the crown clockwise tightens the mainspring for the going train, turning it anticlockwise provides energy for the chronograph function. As a reference to the stopwatch that Minerva launched in 1916, the chronograph button on the Montblanc TimeWalker Chronograph 100 is similarly positioned at “12 o’clock”.
The new wristwatch is affixed to a strap made of black alligator-leather with large reptilian scales. Contrastingly coloured red stitching and a titanium pronged buckle complete the attractive wristband.
The TimeWalker Chronograph 100 epitomizes high performance, inventive mechanisms and precision engineering. The horizontally satin-finished flange along the dial’s circumference is calibrated with a 100th of-a-second scale and printed with a red “100” at “12 o’clock”.
The dial is fabricated from transparent sapphire crystal and offers an unobstructed view of newly developed manufactory Calibre MB M66.25. An especially interesting detail here is the column wheel with its wolf’s teeth at “12 o’clock” which advances by one increment each time the chronograph pusher is triggered; as well as the components of the bidirectional winding mechanism at 3 o`clock.
The ordinary time of day or night is displayed on an anthracite-grey hour-scale framed in silver. This scale is interrupted by a disc of sapphire crystal printed with a scale for the continually running seconds at “9 o’clock” and by the chronograph’s counter for 60 elapsed seconds and 15 elapsed minutes at “6 o’clock”.
Like the hands on all TimeWalker chronographs, the hour-hand and minute-hand are lanceolate and inlaid with strongly luminous Superluminova. The significance of the chronograph function is clearly understandable when one scrutinizes the 100th of-a-second scale and the counters for 60 elapsed seconds and 15 elapsed minutes. The large trotteuse, which is made of lightweight aluminium, is coated with red lacquer; it completes one rotation per second to precisely indicate the measured time to the nearest 100th of a second. The counter at “6 o’clock” is a transparent disc of sapphire crystal marked with two concentric scales, each of which is swept by its own skeletonised lanceolate hand: the longer black hand progresses along the outer scale, which is marked with Arabic numerals for 60 elapsed seconds; the shorter red hand slowly advances along the inner scale, which is calibrated for 15 elapsed minutes.
The screwed titanium back bears a scratch-resistant pane of sapphire crystal, through which connoisseurs can admire the movement’s complexity and its exclusive decorations. The large, massy, screw balance oscillates uninterruptedly and at the comparatively leisurely frequency of 2.5 hertz; the smaller balance begins vibrating at twenty times this speed when the chronograph is switched on. Together, these two balances show how Montblanc’s watchmakers have conjoined the aesthetic perfection of the mechanisms and the greatest precision.
In the TimeWalker Chronograph 100, Montblanc has united innovative constructions, modern material technologies, uncompromising striving toward the utmost performance and traditional manufacture craftsmanship.
The Montblanc TimeWalker Chronograph 100 will become available starting in the autumn of 2014. It will be produced in a strictly limited series of 100 timepieces, each of which will sell for a retail price of € 50,000.
Model: Montblanc TimeWalker Chronograph 100
Manufacture calibre MB M66-25
Manually wound movement with chronograph; one balance for the time indication and a separate balance for the chronograph
Chronograph Monopusher mechanism with column-wheel, button between the horns at “12 o’clock”
Diameter = 38.4 mm, height = 7,63 mm
Number of components: 377
Number of rubies: 37
Power reserve: Ca. 100 hours for the going train, ca 45 minutes for the chronograph
Balance (going train): Screw balance, diameter = 11,4 mm; 26 mgcm2
Frequency going train): 18,000 semi-oscillations per hour (2.5 hertz)
Hairspring (going train): With Phillips terminal curvature
Balance (chronograph): Smooth hoop; diameter = 6 mm;
Frequency (chronograph): 360,000 semi-oscillations per hour (50 hertz)
Hairspring (chronograph): Flat
Plate: Rhodium-plated nickel silver with circular graining on both sides
Bridges: Rhodium-plated nickel silver with côtes de Genève decoration
Gear-train: Gold-plated wheels with faceted spokes, hubs with polished centres
Hours and minutes from the centre, subdial for the seconds at “9 o’clock”
Hundredths of a second from the centre (one revolution per second); concentric counters for 60 elapsed seconds and 15 elapsed minutes at “6 o’clock”
Material mix consisting of titanium, stainless steel and carbon fibre
Crystal above dial: Cambered sapphire crystal
Bezel: Stainless steel coated with black DLC
Middle piece (carrure): Titanium sheathed by a cocoon o carbon fibre
Back of case: Screwed titanium back with inset pane of sapphire crystal
Crown: Titanium with inlaid Montblanc emblem made of mother-of-pearl
Diameter = 45.6 mm, height = 15.48 mm
Water tightness: To 30 meters
Sapphire crystal with several functional levels, continually running seconds shown on a disc of sapphire crystal at the “9 o’clock”, inclined flange with scale for 1/100ths of a second
Rhodium-plated hour-hand and minute-hand with Superluminova; skeletonised, black lacquered hand for 60 elapsed seconds; skeletonised, red lacquered hand for 15 elapsed minutes; red lacquered hand for 1/100ths of a second
Black alligator-skin, hand sewn with contrasting red stitching; pronged buckle made of titanium